How to Use a Manual Tire Changer

Looking for a step-by-step guide on how to use a manual tire changer? You are in the right place.

 

Users can change a tire on its rim using only the tool and their bare hands with manual tire changers. The tool consists of a wheel mount and a pry bar for removing and installing tires. Simply remove the old tire off the rim with the pry bar and pry the new tire onto the rim with the same tool to use the gadget.

 

What is a Manual Tire Changer?

Manual tire changers are useful pieces of equipment; they are inexpensive, lightweight, and simple to operate. The system, which is ideal for DIY enthusiasts, allows you to change your vehicle’s tires at home, saving you money and time by avoiding costly and time-consuming visits to the tire shop. Practically anyone can master these manual tire machines with only a little know-how.

 

Tires are a critical component since they are the only point of contact between the road and your car. As a result, the equipment you use to replace them mustn’t cause any harm. We’ve put together this useful guide to help you know how to use a manual tire changer.

 

READ: Best Exhaust For 5.3 Silverado in 2021

 

How Do You Use a Manual Tire Changer?

Step 1

Press the valve stem to open it and let all of the air out of the tire.

 

Step 2

Place the tire on one of the tire changer’s legs that has a triangular wedge protruding up from it. The wedge should be positioned such that it touches the rim directly where the tire’s edge meets the rim.

 

Step 3

In the area between the tire and the rim, place the drop-down wedge. Pry the tire from the rim by inserting the pry bar into the slot on the side of the tire changer and pushing it down.

 

Step 4

Repeat Steps 2 and 3 after rotating the tire 180 degrees.

 

Step 5

Repeat steps 2, 3, and 4 on the other side of the tire.

 

Step 6

Remove the top of the machine and set the tire on the exposed stem. Screw the machine’s top back on and place the “spider” lock washer on top of the tire.

 

Step 7

Using grease, lubricate the tire’s edge. To remove the tire’s edge from the rim, place the flat end of the pry bar in the space between the tire and the rim and revolve the pry bar clockwise around the tire.

 

Step 8

Raise the tire and put the flat end of the pry bar into the gap between the tire and the rim on the other side. To completely remove the tire from the rim, rotate the pry bar clockwise around the tire.

 

Step 9

Apply lubrication along the new tire’s edges. Place the new tire on the rim.

 

Step 10

Insert the pry bar’s flat end into the gap between the tire and the rim. Raise the pry bar to pry the tire’s edge over the rim’s edge. Rep around the circumference of the tire until it is totally on the rim on that side.

 

Step 11

Push the tire down until the side on the rim makes contact with the rim on the other side. In the space between the remaining side of the tire and the rim, insert the hook end of the pry bar. Pry the tire off the rim by rotating the pry bar clockwise around the tire.

 

Finally, remove the tire from the tire changer by hand.

 

READ: The Best Center Punch Tools

 

FAQs

How does a tire spreader work?

Tire spreaders are commonly used to check and repair tires, as they allow you to peel apart the beads of a tire to see the internal hollow. These tools are very useful for dealerships, fleet repair centers, tire shops, and other businesses that work with cars.

 

Is it worth it to change your tires?

Many shops charge $60 more to change unmounted tires than to swap tires on wheels, so it only takes a few seasonal changes to pay for the rims, and it pays even faster if you change your tires.

 

Do you need a torque wrench to change tires?

In most circumstances, a torque wrench is not required; the spare jack and tire iron that come standard with every automobile are adequate to change a tire. If this were the case, automakers would have to start including torque wrenches in their vehicles in the event of a flat tire.

 

How hard is it to change a tire?

Changing a tire is a physically difficult process. You’ll need some strength to remove the lug nuts and crank the jack, and then you’ll need to bend down and lift the tire. People frequently try to rush through all of this to get on their way, but this is a mistake.

 

Is the wheel held in place by a manual tire changer?

To limit tire movement when working the bar around the edges, most tire changers have washers that are typically screwed onto the rim of the tire. Some models also come with a stand that holds and stabilizes the tire while you work on it.

                                                                                                                 

Is it possible to balance wheels using a tire changer?

It depends on the tire changer’s design. Wheel balancing tools are included with some models to balance the tire weight and wheel assembly. At high speeds, this reduces tire vibration. Most tire changers, on the other hand, just have a bead breaker and rim support for mounting and dismounting tires.

 

Wrapping Up

Quality and durability should both be considered when choosing the correct tools. We understand that not all users and business owners can afford top-of-the-line equipment right now. However, there are a few manual tire changers from well-known companies that will give your new shop a professional look without breaking the bank.

Click Here to Leave a Comment Below 0 comments