Best PEX Crimp Tool Review in 2018 | Top Picks For Plumber

When dealing with wires which are delicate or those that are core in the wiring system, which if interfered with can affect the entire wiring. You need tools that are sturdy enough to do the job while at the same time carefully so as to make accurate cuts.

For that reason, when trying to complete wiring projects around the house, you can testify on how hard it is to cut the wires. Instead of getting a hard time with the cables, you can make the work simpler by using a crimping tool.

Crimping tools efficiently and quickly bends, strips, cuts and crimps insulated cables. It is essential that you get the best PEX crimping tool quality for yourself. One that is durable and still gives you the best results. Read on to get a compiled list of the best PEX crimp tools according to customer’s reviews.

Look at the comparison table. we will provide you with more information that will help you in our Buyer’s Guide later.

Reviews of The Best PEX Crimp Tool

Iwiss F1807 PEX Pipe Crimping Tool Kit

It provides a steady and leverage platform to work on for continuous crimping. Its crimp and trim system which is original helps to ensure a flush trim cleanly on the conductors.

The tool is also, of recommendable quality; it is solidly built and has a lot of power. The stripper and cutter feature, which are in-built, provides you with everything you need with just one tool.

Highlighted Features

  • It delivers a flush trim plainly on the conductors
  • check
    Interchangeable jaws of 3/8”, 1/2", 3/4"
  • check
    Comfortable handle
  • check
    It meets ASTM F 1807 standard.

Customer Question on Iwiss Pex Crimp Tool

Q:  what disparity is there between the short kit and the large kit?

A: the difference lies in only the crimping length. The short kit is shorter hence; you end up using more effort during crimping. However, it allows you to crimp in tight space areas, and the handles open 180 degrees to get over the pipe. It will not be possible for you to work in a cramped area using the full length of the great kit.

Q: Is it possible to crimp a 1 inch?

A: Yes, you will crimp without the jaws

Q: does the tool feature ratcheting system?

A: no

Q: Is it possible to get a replacement when the tool parts break?

A: visit their website iwiss.com/support where you will get help since they offer service and part replacement.


Sharkbite 23​2551 PEX​ Crimping Tool

The tool features an easy to connect system which favors beginners. It is dual headed allowing you to work on the two most common copper heads without the need of changing the heads. The tool is versatile; it is suitable for both wet and dry conditions.

Also, the device is compatible with many other machines due to its nature of being easy to install, flexible and reliable. It also makes crimping fast and easy as you do not have to wait for joints to cool or glue to dry. As world leaders of the plumbing solution called push- connect, you can be sure of the quality of this crimping tool. 

Highlighted Features

  • Has a go/no-go gauging tool  
  • check
    Compatible with other devices such as PEX pipe tubing, pex 1/2” and 3/4 “ copper crimp and PEX barb fittings    
  • check
    Dual headed with a shark bite of PEX 3/4” and 1/4" crimp rings.
  • List Element

Customer Question On Sharkbite 23251 PEX Crimping Tool

Q: which crimp rings work well with this tool?

A: use copper rings only

Q: does the tool feature go/no-go system?

A: yes the feature is included

Q: is it possible to open the crimp tool and still get to the fitting area that is within the floor joists space?

A: it depends on the direction which the plumbing is done. However, in most cases space fits the tool.

Q: is the tool made in China or the USA?

A: the tool is made in the USA


Apollo PEX 69PTKG1096 Pinch Clamp Tool

It is a bonus to have this tool around as it will assist you in completing challenging tasks. Besides, the tool has an inbuilt adjustment.

It will help you to release the lever if the terminal is wrongly placed. Its construction is powerful hence; the tool will last for many years before you replace it.

Highlighted Features

  • Go/no-go crimp gauge
  • check
    An open jaw in 3/8”, 1/2”, 3/4", and 1”
  • check
    The wrench can change jaws hence, adjusts its crimping force

Customer Question On Apollo Pex 69PTKG1096 Clamp Tool

Q: does the toolkit come with a PEX cutting tool are should you buy it separately?

A: the kit does not have a PEX cutting tool. You can, however, buy a cheap one to save on cost

Q: is the device compatible with Viega system?

A: it depends on the Viega fitting that you are referring since the tool works well with the Viega manabloc. While it is not recommendable to use it with the Viega press-fit fittings, they have their specific tool that should be used together.

Q: does the tool have an adjustment screw for increasing tension?

A: yes, it does

Q: can it work on 15mm and 22mm copper wire?

A: no, the tool is only for PEX pipes but not copper wires. When used with copper crimp rings, the ring will slip over the exterior side of the tube to the area where the fitting is inserted. You can then crimp it down to secure the connection of the accessory.


Zurn Steel Multi-head Copper Crimp Tool

If you are a plumber, you have a similar need for a quality tool as an electrical person. Zurn crimp tool is essential to have around. It features a Go or no-go gauge which will help you in counter checking the preciseness of your crimping job.

For additional assurance, you can check on the crimps after the tool has compressed. Also, it installs 3/8”, 1/8”, 5/8”, and 3/4” fittings of PEX. The tool has an open end wrench and jaw thus allowing for the adjustment of crimping force. In addition, the crimp tool has a reliable steel construction guaranteeing its durability.

Highlighted Features

  • Reliable steel construction    
  • check
    Five tools
  • check
    Compatible jaws for 3/8”, 1/8”, 5/8” and ¾” of PEX fittings that have copper crimp rings
  • check
    It has a go/ no-go gauge and a crimp removal tool.

Frequently Asked Question

Q: Can the tool open a 1” wide die?

A: No, because the jaws are not wide enough to work on an inch die.

Q: Can the crimp work on stainless steel?

A: no, since the stainless cinch technology is different from copper crimp rings, the crimp works best on only copper rings.

Q: how do you use the crimp gauge?

A: the most critical crimping step is confirming that the metal ring which you are working on can slide easily inside the gauge. It is recommended that the crimp ring should be smaller than the gauge. It indicates that the connection is good. However, if the ring is more prominent, it means the ring is not set correctly. You should remove it and reset it so that the pipe does not leak.


Iwiss PEX Crimping Tools Cinch Clamp Tools.

The tool has a go/ no-go gauge which makes it easy for you to check the crimps after compressing for assurance. Also, it features a ratcheting system which releases the connectors before the tool fully condenses.

The mechanism ensures excellent performance and also prevents the device from slipping. The apparatus has an open end wrench and jaw which are 3/8”, 1/2", 3/4" and 1”. The tool is versatile and works well with pipes in both wet and dry conditions.

Highlighted Features

  • It has a ratcheting system which is a self-releasing mechanism of ensuring a thorough crimp
  • check
    It is compatible with all cinch clamps except the Zurn quick clamp
  • check
    It does not require any adjustment or calibration as it is factory adjusted
  • check
    It has a go/no-go gauge
  • check
    It works perfectly with stainless steel clamps of 3/8”, 1/2", 5/8”, 3/4" and 1”
  • check
    Has a comfortable handle which long hence minimizes fatigue

Customer Question On Iwiss PEX crimping tool

Q: What is the total length of the tool exclusive of the package?

A: the tool is 12 inches in length

Q: IS the tool compatible with Zurn tubing?

A: no, the tool does not work with Zurn tubing. It is only compatible with F2098 standard

Q: is the tool made in USA or China?

A: the crimp is made in China but is of high quality and undergoes strict tests before delivery.

Q: does it feature a calibration gauge?

A: no, but when you see a dimple (crimps) in the middle it means your crimping will be secure and accurate


Iwiss F 1807 Combo Crimping Tool

The IWISS F1807 Combo Set, that comes with a truly innovative design, along with everything you will need to get started with your plumbing.  IWISS is a great plumbing company that provides durable and high quality products, and the F1807 is no different.

Even if anyone uses the tool for first time, it is very easy and simple for him to install the pipe. 

Highlighted Features

  • Meets the ASTM F 1807 standard
  • check
    A 1/2" and 3/4” combo crimping tool
  • check
    Strong and durable due to the steel materials that make it
  • check
    Has a smart design that makes it easy for the tool to get to the installation areas easily
  • check
    Perfectly polished hence, ensuring no damage to the copper rings.
  • check
     It also makes crimping easy as all you have to do is pull back the handles to open the jaws then crimp.

Customer Question on this tool

Q: is the tool calibrated?

A: it is factory calibrated and does not require the standard calibration

Q: does it work for both copper and PEX pipe?

A: it is made for the PEX pipe

Q: the go/ no-go feature works entirely different. How do you go about it?

A: when the thing is halfway, your crimping is correct. However, if it goes to the end at the opening side or goes entirely around the crimp, know your joint has been damaged. In short, halfway is go and more than halfway is a no-go.

Q: how do you go about calibrating the tool when you want?

A: remove the ‘c’ of the word clamp with a screwdriver. Then, rotate the pin by pushing it and increase by a single increment only. Now replace the ‘c’ with piler. However, it is not necessary for you to go through all that trouble since the tool is easy to use.

Q: it crimps the 3/4 “perfectly, but crimps the 1/2 “oval, any ideas?

A: crimp the ½ inch using a PEX/ fitting


Apollo PEX 69PTKH0015K Multi-head Crimp Tool 

It is an incredible model for the money. It will help you complete difficult tasks with ease. It has an inbuilt adjustment which lets you release the lever in case the terminal was wrongly placed. Its construction is very sturdy, guaranteeing durability.

Also, there is no loose connections thus better productivity. Its leverage gives it a steady platform for better termination. The tool’s surface allows the tool to hold in place with the surface securely.

Highlighted Features

  • Go/ no-go gauge
  • check
    The adjustable crimping force with the wrench having changeable jaws
  • check
    Has an open-end wrench and jaw which is 3/8”, 1/2", 3/4" and 1”

Customer Question On Apollo 69PTKH0015K pex

Q: what type of clamp are you supposed to use with this tool?

A: use it with the smooth copper rings most commonly the 1/2” and 3/4"

Q: can it be used on quest pipes?

A: there is no mentioning whether it is compatible. Maybe it is because huge class action suits highly discourage its use due to its high chances of failure.

Q: can you use the tool to replace land mower control cables?

A: the tool is only made to replace PEX pipe of 3/8 to 1 inch. It cannot work in a land mower.

Q: where can I get a replacement for the sheer pin and snap ring?

A: you can get the snap ring from a local shop. Alternatively, buy a metric snap ring and it will suit the tool. You can also contact Amazon. 


Iwiss PEX Pipe Crimping Toolkit with Pipe Cutter

In the end, the wrench is open and allows the jaws to measure 3/8”, 1/2", 3/4" and 1”. Furthermore, the tool allows you to adjust your crimping force. The tool is sturdy, well-built guaranteeing a long life before replacement is required.

Also, the tool is lightweight making it easy to handle and store it. The tool has an ergonomic handle which gives it a comfortable grip hence reducing fatigue. It is also compatible with all fittings as long as they follow the ASTM F 1807

Highlighted Features

  • It meets the standards stated in the ASTM F 1807
  • check
    Has an open wrench with jaws of 1/2", 3/4”, 3/8” and 1.”
  • check
    Its changeable jaws and adjustment features do its work effectively.
  • check
    It has a short length, and it is lightweight hence reducing fatigue while still, it can work in tight areas.
  • check
    It also has a comfortable handle further decreasing fatigue
  • check
    Works with copper crimp rings only
  • check
    Its polished jaws and perfect locator hence ensure the copper pipes and rings are not damaged

Frequently Asked Question.

Q: does the tool work well with Apollo crimp rings?

A: it should work just fine as long as the rings are copper and meet the standards stipulated in ASTM F 1807

Q: Is this crimping adjustable to infinite length?

A: What do you mean by infinite? The crimp tool, however, has adapters which enable it to expand further when dealing with full range pipe.

Q: Is this tool made in the US?

A: No, it is made in China


Iwiss Combo Angle Head PEX Crimping Toolkits

The tool has polished jaws ensures that it does not damage the copper rings. The tool also has a comfortable grip which makes it easier to crimp with. Furthermore, the tool is factory calibrated hence, you do not need to adjust during the first few times of use after purchase.

Highlighted Features

  • The tool meets the standard specification stated in ASTM F 1807
  • check
    It has an open, combined wrench that has both 1/2” and 3/4"It is also easily calibrated
  • check
    It makes it easier to crimp small corners.
  • check
    Its model enables you to curb fatigue
  • check
    It is compatible with all US F 1807 standard tools.

Frequently Asked Question

Q: How much space does the tool require for it to operate and can it work in tight space?

A: Yes, the tool works well even in tight spaces. You only require a space of 10 inches.

Q: Does the tool crimp Apollo ring?

A:  Yes, it works well with any copper rings as long as it meets ASTM F 1807

Q: What is the tools length measurement in inches excluding the case?

A: The tool has a length of 11.5 inches.

Q: Please explain how the tool is used

A: When you pop back the handles, the jaws open up

Q: Can you use the tool in crimping a polybutylene pipe?

A: Yes, both the PEX and poly have the same total diameter this makes it possible for the tool to work on both.


Buyer’s guide

With all crimp tools manufacturers and many crimp tools in the market it can be difficult to know which one to pick. How do you pick out one that will suit your needs? This guide aims at helping you understand the features you ought to look for in a crimping tool to avoid disappointments.

Ergonomic and soft handle

Sometimes crimping requires use of a lot of force, if the handle is hard you can end up with a blistered hand. A comfortable grip is also essential in case your job requires frequent use of the tool.

Durability

A crimping tool should provide service to you for a long time without frequent repairs to save you the cost. It is essential that you analyze the materials used to make the crimp tool and ensure it is constructed using rugged steel.

It is sturdy and guarantees you durability. The pressure control system also provides a longer life for the device.

Adjustable

You should choose crimp tools which are modifiable as it will enable you to work with crimps of different sizes using the same tool. It will indirectly help you to save on cost as you will not have to buy many crimp tools for each size.

Lightweight

You should choose a crimping tool which is easy to carry and handle. A heavy one will tire the hand and cause low job performance also, it makes it easier to store it when it is not in use. A proper crimp tool should be made using heavy duty materials but be of lightweight.

Ratcheting design

It is essential as it ensures the connectors are released before it fully compresses. It gives you more control over your job. In addition, the mechanism creates a non-slip environment during crimping. It, hence, will ensure your safety in addition to excellent performance.

Price

All crimpers are offered at their own different price. Typically, the more money you are willing to invest the better your crimp tool performance will be.  In addition, going for the best brand also guarantees you greater productivity and durability.

Task volume

When you are choosing a crimp tool consider the size of the task you want to complete. For instance, if you will be using the tool consistently, you should go for an automated crimp tool. Your priority should be one with either a hydraulic system or a pneumatic press.

Intended purpose

Before you purchase the best crimping tool, it is vital that you understand your needs. It will help you compare with the function of the device ensuring you have something of value. There are various crimping tools which are best with network cables, plumbing and computers. It is hence, vital that you know the best crimping tool for your career.

PEX cinch vs. crimp

The best PEX cinch has many advantages over the crimping style. Its primary advantage is that a single tool works with different PEX sizes. The crimping tool on the other hand, has limitations on the sizes of PEX it can work with.

It means that you may require a different crimping tool for different jobs while a cinch works on all PEX jobs you are finishing on. Furthermore, the cinch is more corrosive resistant as compared to crimp tools. Finally, cinch tool operation is easier to understand when compared with the crimp tools.

At last, let's enjoy a video on How to calibrate your PEX Clamp Tool

Click Now To Share!
Click Here to Leave a Comment Below 0 comments